European equivalent grade for Non-alloy quality structural steel A572 ( AISI, ASTM, UNS):S355JR (1.0045) Cross reference table for Steel A572 ( AISI, ASTM, UNS) and its European equivalent S275J2(+N) (1.0144) ( EN ) A572 Structural, Carbon & HSLA Steel Plate - Chapel SteelA high-strength low-alloy steel plate that is utilized in a variety of structural applications. This specification is produced in Grades 42, 50, 55, 60 & 65, the grades representing the yield strength.
A572 steel is available in five different grades:42, 50, 55, 60, and 65. Each grade number indicates the yield strength of this high strength, low alloy steel. Its multiple favorable properties make it a staple for construction applications. ASTM Structural Steel Standards Infra-Metals Co.A572 steel is available in five different grades:42, 50, 55, 60, and 65. Each grade number indicates the yield strength of this high strength, low alloy steel. Its multiple favorable properties make it a staple for construction applications. ASTM Weathering Steel Specifications Central Steel ServiceASTM A572-65. ASTM A572-65 is a high strength low-alloy columbium-vanadium structural steel. This specification provides for a 65ksi minimum yield strength and an 80ksi minimum tensile strength. The primary application for ASTM A572-65 is galvanized transmission and lighting poles.
Standard:EN10025-2 . Steel Grade:S355J2, S355JR, S355J0, S355K2, S450J0. Nearest Equivalent:DIN 17100 ST52-3; ASTM A572-50; JIS G3106 SM490; JIS 3101 SS490 . ABS EH36; LRS EH36; BS4360 Grade50D; BS4360 Gr50DD S355J2+N High Tensile Steel Plates. S355 offers high yield and THE BEST WEIGHT LOSS PILLS tensile strength with a minimum yield strength of 355 N/mm² , a structural grade EN10025 S275 Steel S275JR Properties, Equivalent, Meaning EN 10025 S275 steel properties, composition and equivalent materials can be found in the following datasheet. All data sheet of DIN EN 10025-2 is the same as BS EN 10025-2 and other EU member states. Chemical Composition. Datasheet 1, EN10025 S275J0, S275J2 and S275JR chemical composition based on ladle analysis is given in the following table. LM555 Timer datasheet (Rev. D) - Texas InstrumentsLM555 ti SNAS548D FEBRUARY 2000REVISED JANUARY 2015 6.5 Electrical Characteristics (TA = 25°C, VCC = 5 V to 15 V, unless otherwise specified)(1)(2) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Supply Voltage 4.5 16 V Supply Current VCC = 5 V, RL = 3 6 V mA CC = 15 V, RL = 10 15 (Low State) (3) Timing Error, Monostable
Q235 Steel (Q235A Q235B Q235C Q235D) Q235 steel is a plain carbon structural steel which is widely used in China, Q235 material in Chinese standard GB/T 700 is divided into 4 quality grades:Q235A, Q235B, Q235C and Q235D; Density of this steel is 7.85 g/cm3, tensile strength is 370-500 MPa; yield strength is 235 MPa (data are for steel bar or steel plate diameter 16mm). STATISTICAL ANALYSIS OF CHARPY V-N TOUGHNESS A572 Gr50 HR A572 Gr50 QST A913 Gr65 QST A588 HR Dual grade (A36 and A572 Gr50) ASTM A673 defines a test as the average of three specimens. Most data reported to AISC was the three required test values and the average of these three values. The total number of CVN values reported to AISC was 21,330. Also, the total number of STRUCTURAL STEEL SECTION FACTOR General GuidelinesUniversal Beams (UB Section) 13-15 Table 5. Universal Columns (UC Section) 16 Table 6. Universal Bearing Piles (UBP Section) 17 NOTES 55-56. 1 For example, at 700°C, the effective yield strength of Grade 43 (S275) steel is 0.23 x 275 = 63.25N/mm2
Universal Beams (UB) Dimensions and properties Universal Beams (UB) sizes Designation Serial size Mass per metre kg/m Depth of section Width of section Thickness Root radius Depth 308 35 353 55 0.874 27.5 0.0280 9.57 36.1 254 x 102 x 28 351 61 393 94 0.880 29.6 0.0660 8.55 39.7 254 x 146 x 31 Standard I-Beam Gerdau WebsiteStandard I-Beam Gerdau produces hot-rolled Standard I-Beams, most commonly used by original equipment manufacturers (OEM) in the construction of machines and equipment, lifts and hoists, maritime platforms, overhead cranes and monorails. These beam sections are available in a wide range of sizes, from 3 x 5.7# to 12 x 31.8#. WIDE FLANGE SHAPESshapes are widely used for beams, columns and other architectural members, as well as in pile foundations, Rough universal mill Cooling bed Roller straightener Shipment of products. 4 Specifications 4 (2) Corresponding Specifications ASTM BS ASTM A36, A572 A572 Gr
Wide Flange Beam Gerdau hot-rolled wide flange (WF) beams are used in structural steel construction, in applications from industrial facilities and health care to commercial buildings and multi-family residential projects. ASTM A572-50 (A709-50) ASTM A572-55: 4" - 36" (up to 210 lbs/ft) Beam Depth Catalogs. Structural Products Bundles steelwise Keeping tabs on ASTM specifications aRE yOU ASTM A529 Grade 50 and 55, ASTM A572 Grade 42 and 50, and ASTM A913 Grade 50. M-Shapes and S-Shapes The preferred material specification for M-shapes is in tran-sition. ASTM A36 (F y = 36 ksi, F u = 58 ksi) remains common, but 50 ksi grades increasingly are being used, including ASTM A572 Grade 50, ASTM A529 Grade 50 or ASTM A992; each ASTM A572 - SSABASTM A572 includes five grades with specified minimum yield strengths of 42, 50, 55, 60, and 65 ksi, respectively. For applications where notch toughness is important, consult SSAB for specific Charpy V-notch toughness requirements. ASTM A572 grades are used in a wide variety of structural applications in many market segments.